JVC CS-AW7040 Manuel utilisateur

ENGLISH
CAISSON DE GRAVE
CS-AW7020
CS-AW7220
CS-AW7040
CS-AW7240
CS-AW7020
CS-AW7040
CS-AW7220
CS-AW7240
For Customer Use:
Enter below the Model No, and Serial
No, which is located either on the rear
or bottom of the speaker unit. Retain
this information for future reference.
Model No.
INSTRUCTION MANUAL
MANUEL D'INSTRUCTIONS
MANUAL DE INSTRUCCIONES
Serial No.
LVT1743-001A
ESPAŃOL FRANÇAIS
SUBWOOFER
ENGLISH
Thank you for purchasing the ARSENAL Car Stereo Speaker. These Speakers can be
mounted in the trunk of your vehicle. For the secure installation and perfect operation
of your speakers, please read the following carefully.
Parts
2. Screw x 10
3. Jump
4. Fuse (10A) x 2
5. Hexagon socket
screw keys
1. Grille
For proper installation and use
1.Before connecting the speakers to the amplifier, confirm that the power has been
turned off. The click noise generated by the connection if the power is on may
damage the speakers.
2.The amplifier and speakers should be connected between corresponding terminals,
i.e. left to left, and right to right, as well as "+" to "+", and "–" to "–". Connection with
reversed polarity will degrade the quality of stereo reproduction.
3.Do not subject the speakers to excessive input. The power handling capacity of the
CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 is 600 watts (R.M.S. MUSIC
POWER). Any excessive input may damage the speakers.
4.The CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 has an impedance of 2Ω
,4Ω,8Ω. Make sure that the output impedance of the amplifier's speaker terminal is
rated at 2Ω,4Ω,8Ω.
5.When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not
apply thinner or solvent.
6.Be sure to carefully follow the instructions for:
Cable Connections
Fuse Replacement
Switching the Impedance Selector
Subwoofer Mounting and Smart Trim Ring Installation
Consult Page 19 of this Instruction Manual for details on these procedures.
-2-
Dual 4 Ω Application Diagrams
SERIES
JUMPER
1 Mono Amplifier
1 Subwoofer
Jumper set to Parallel
8Ω(4Ω+4Ω) Load
PARALLEL
SERIES
Jumper Plug
-
+
Mono
Bi-Amp
Only
Input
4Ω
Input
-
+
PARALLEL
Jumper Plug
Input
ENGLISH
JUMPER
1 Mono Amplifier
1 Subwoofer
Jumper set to Series
8Ω(4Ω+4Ω) Load
-
+
Mono
4Ω
8Ω
Bi-Amp
Only
Input
-
+
4Ω
4Ω
2Ω
*JUMPER is Removed
1 2ch Amplifier
1 Subwoofer
Jumper is Removed
4Ω Load
SERIES
Input
Stereo
-
+
Bi-Amp Configuration 2 Mono Amplifiers
1 Subwoofer Jumper is Removed 4Ω Load
*JUMPER is Removed
PARALLEL
Bi-Amp
Only
+
SERIES
Mono
Input
-
Input
-
+
4Ω
PARALLEL
Bi-Amp
Only
Input
-
+
Mono
4Ω 2-Chan
4Ω
JUMPER
1 Mono Amplifier
2 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel
4Ω Load
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
4Ω
Bi-Amp
Only
Input
-
+
Input
-
+
4Ω
8Ω
PARALLEL
Jumper Plug
4Ω
Bi-Amp
Only
Input
-
+
4Ω
8Ω
4Ω
JUMPER
1 Mono Amplifier
3 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel
2.6Ω Load
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
4Ω
Bi-Amp
Only
-
Input
-
+
4Ω
4Ω
8Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Bi-Amp
Only
Input
-
+
Input
-
+
4Ω
8Ω
PARALLEL
Jumper Plug
4Ω
Bi-Amp
Only
Input
-
+
4Ω
8Ω
2.6Ω
JUMPER
1 Mono Amplifier
4 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel
2Ω Load
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
4Ω
Bi-Amp
Only
8Ω
-
4Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
4Ω
Bi-Amp
Only
8Ω
2Ω
-3-
-
4Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
4Ω
Bi-Amp
Only
8Ω
Input
-
+
4Ω
PARALLEL
Jumper Plug
Input
-
+
4Ω
Bi-Amp
Only
8Ω
+
Input
-
4Ω
Dual 2 Ω Application Diagrams
SERIES
JUMPER
1 Mono Amplifier
1 Subwoofer
Jumper set to Parallel
4Ω(2Ω+2Ω) Load
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
Bi-Amp
Only
Input
2Ω
Input
-
+
PARALLEL
Jumper Plug
ENGLISH
JUMPER
1 Mono Amplifier
1 Subwoofer
Jumper set to Series
4Ω(2Ω+2Ω) Load
-
+
Mono
2Ω
4Ω
Bi-Amp
Only
Input
-
+
2Ω
2Ω
1Ω
*JUMPER is Removed
1 2ch Amplifier
1 Subwoofer
Jumper is Removed
2Ω Load
SERIES
Input
Stereo
-
+
Bi-Amp Configuration 2 Mono Amplifiers
1 Subwoofer Jumper is Removed 2Ω Load
*JUMPER is Removed
PARALLEL
Bi-Amp
Only
+
SERIES
Mono
Input
-
Input
-
+
2Ω
PARALLEL
Bi-Amp
Only
Input
-
+
Mono
2Ω 2-Chan
2Ω
JUMPER
1 Mono Amplifier
2 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel
2Ω Load
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
2Ω
Bi-Amp
Only
Input
-
+
Input
-
+
2Ω
4Ω
PARALLEL
Jumper Plug
2Ω
Bi-Amp
Only
Input
-
+
2Ω
4Ω
2Ω
JUMPER
1 Mono Amplifier
3 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel
1.3Ω Load
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
2Ω
Bi-Amp
Only
-
Input
-
+
2Ω
2Ω
4Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Bi-Amp
Only
Input
-
+
Input
-
+
2Ω
4Ω
PARALLEL
Jumper Plug
2Ω
Bi-Amp
Only
Input
-
+
2Ω
4Ω
1.3Ω
JUMPER
1 Mono Amplifier
4 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel
1Ω Load
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
2Ω
Bi-Amp
Only
4Ω
-
2Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
2Ω
Bi-Amp
Only
4Ω
1Ω
-4-
-
2Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
2Ω
Bi-Amp
Only
4Ω
Input
-
+
2Ω
PARALLEL
Jumper Plug
Input
-
+
2Ω
Bi-Amp
Only
4Ω
+
Input
-
2Ω
When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also
recommended for the enclosure materials.
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
A 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
B 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
C 11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm)
D 9-4/32 inch (232 mm)
10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm)
11-10/32 inch (295 mm)
F 4/32 inch (3 mm)
4/32 inch (3 mm)
3
3
G 1.57 ft (0.045 m )
2.17 ft3 (0.062 m3)
Front & Rear Baffle Boards (x 2)
C
B
Top & Bottom Sides (x 2)
G : Internal Volume
A
Left & Right Sides (x 2)
Mounting Hole
Dimension
* Screw: Dia. 4mm x 50mm (x 8) (supplied)
To install the ported enclosure
When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also
recommended for the enclosure materials.
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm)
B 18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm)
C 13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm)
D 9-23/32 inch (247 mm)
10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm)
11-10/32 inch (295 mm)
F 4/32 inch (3 mm)
4/32 inch (3 mm)
G 1 inch (25.4 mm)
1 inch (25.4 mm)
H 13 inch (330.2 mm)
14 inch (355.6 mm)
I 13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm)
Front & Rear Baffle Boards (x 2)
J 1.85 ft3 (0.052 m3)
2.54 ft3 (0.072 m3)
C
B
Top & Bottom Sides (x 2)
J : Internal Volume
A
Left & Right Sides (x 2)
G
I
* Screw: Dia. 4mm x 50mm (x 8) (supplied)
H
- 5-
Mounting Hole
Dimension
ENGLISH
To install the sealed enclosure
ENGLISH
Parameters
Nominal Impedance (Ω)
SPL (dB,1W/1M)
Displacement (Liter)
Hole Cutout Diameter (inch)
(mm)
Mounting Depth (inch)
(mm)
Re (Ω)
BL (T.M)
Vas (Liter)
Vas (CuFt)
Me (g)
D (mm)
CS-AW7020
CS-AW7040
NOTES
parallel
series
parallel
series
2Ω + 2Ω
4Ω + 4Ω
83.49 dB 83.54 dB 84.02 dB 84.12 dB SPL : Sound pressure level
0.123 ft3
Dia. 9 - 6/32 inch
( 233 mm )
6 - 14/32 inch
( 163.5 mm )
0.98 Ω
3.83 Ω
1.92 Ω
7.6 Ω
Re : DC voice coil resistance
6.85
13.75
8.68
17.21
BL : Product of Flux density and
Effective Voicecoil-wire length
17.08 L
16.98 L
18.08 L
18.28 L
Vas : Volume of air equal to the driver
compliance
0.6 ft3
0.599 ft3
0.64 ft3
0.65 ft3
145.986 g 147.109 g 124.084 g 122.443 g Me : Effective mass
Dia. 202 mm
D : Effective cone diameter
Fs (Hz)
39.6 Hz
39.5 Hz
41.7 Hz
41.8 Hz
Qms
10.261
10.282
9.021
9.169
Qes
0.756
0.74
0.83
0.824
Qts
0.704
0.691
0.76
0.756
600 W
Pe [max.] (W)
14.95 mm
Xmax.(mm)
Freq.Responce (Hz)
Magnet Mass (oz)
(g)
Voice Coil(Aluminum)Dia.(inch)
(mm)
Hvc (mm)
Hag (mm)
Parameters
Nominal Impedance (Ω)
SPL (dB,1W/1M)
Displacement (Liter)
Hole Cutout Diameter (inch)
(mm)
Mounting Depth (inch)
(mm)
Re (Ω)
BL (T.M)
Vas (Liter)
Vas (CuFt)
Me (g)
D (cm)
14.8 mm
25 ~500 Hz
65.4 oz
( 1854.1 g )
Dia. 2 - 5/32 inch
Dia. 2 - 4/32 inch
54.5 mm
53.59 mm
39.9 mm
39.6 mm
10 mm
Hvc : Voice coil Height
Hag : Gap Height
0.98 Ω
3.84 Ω
1.94 Ω
7.61 Ω
Re : DC voice coil resistance
6.84
13.72
9.56
19.14
BL : Product of Flux density and
Effective Voicecoil-wire length
38.7 L
38.76 L
35.23 L
35.05 L
Vas : Volume of air equal to the driver
compliance
1.37 ft3
1.37 ft3
1.24 ft3
1.24 ft3
171.854 g 172.934 g 157.028 g 157.336 g Me : Effective mass
Dia. 246 mm
D : Effective cone diameter
34.6 Hz
34.5 Hz
37.9 Hz
38 Hz
Qms
10.277
10.089
8.931
9.014
Qes
0.786
0.765
0.794
0.781
Qts
0.73
0.711
0.73
0.719
600 W
Pe [max.] (W)
Freq.Responce (Hz)
Magnet Mass (oz)
(g)
Voice Coil(Aluminum)Dia.(inch)
(mm)
Hvc (mm)
Hag (mm)
Qms : Q of driver at Fs considering
only non-electrical resistance
Qes : Q of driver at Fs considering
only electrical resistance
Qts : Total Q of driver at Fs
Pe[max.] : Maximum continuous input
power
Xmax. : Maximum effective voicecoil
travel without distortion
CS-AW7220
CS-AW7240
NOTES
parallel
series
parallel
series
2Ω + 2Ω
4Ω + 4Ω
85.13 dB
85.2 dB
85.87 dB 85.65 dB SPL : Sound pressure level
0.18 ft3
Dia. 10 - 29/32 inch
( 277 mm )
7 - 6/32 inch
( 182.5 mm )
Fs (Hz)
Xmax.(mm)
Fs : Driver free air resonance
14.95 mm
14.8 mm
23 ~500 Hz
86.2 oz
( 2443.7 g )
Dia. 2 - 4/32 inch
Dia. 2 - 5/32 inch
( 53.59 mm )
( 54.5 mm )
39.9 mm
39.6 mm
10 mm
-6-
Fs : Driver free air resonance
Qms : Q of driver at Fs considering
only non-electrical resistance
Qes : Q of driver at Fs considering
only electrical resistance
Qts : Total Q of driver at Fs
Pe[max.] : Maximum continuous input
power
Xmax. : Maximum effective voicecoil
travel without distortion
Hvc : Voice coil Height
Hag : Gap Height
Nous vous remercions pour I'achat d'un haut-parleur auto stéréo de ARSENAL dans
le coffre de votre véhicule. Pour un montage sûr et un fonctionnement parfait de ce
haut-parleur, il est conseillé de lire attentivement ce qui suit.
2. Screw x 10
3. Jump
4. Fuse (10A) x 2
5. Hexagon socket
screw keys
1. Grille
Montage et utilisation corrects
1.Vérifier que l'alimentation est coupée avant de raccorder les haut-parleurs à
l'amplificateur. Les craquements produits par le raccordement lors que l'alimentation
est fournie peuvent endomma ger les haut-parleurs.
2.Raccorder les bornes correspondantes de l’amplificateur et les haut-parleurs,
c'est-à-dire, gauche à gauche, droit à droite, de même que “+” à “+” et “–” à “–”. Un
raccordement effectué en inversant les polarités réduira la qualité de la reproduction
sonore stéréo-phonique.
3.Ne pas appliquer un niveau d'entrée excessif aux haut-parleurs. La puissance
d'entrée admissible pour les haut-parleurs
CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 est de 600 watts (puissance
musicale R.M.S.). Tout signal d'entrée excessif risque de les endommager.
4.Les haut-parleurs CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 ont une
impédance de 2Ω,4Ω,8Ω. ll faut par conséquent s'assurer que l'impédance de sortie
aux bornes de haut-parleur de l'amplificateur soit aussi de 2Ω,4Ω,8Ω.
5.Nettoyer le haut-parleur en le frottant légèrement à l'aide d'un chiffon doux. Ne
jamais utiliser de solvants ni de détergents.
6.Veuillez suivre attentivement les instructions suivantes pour:
Connections de Câble
Remplacement de Fusible
Changement de la Sélection d'Impédance
Montage du Subwoofer et Installation Pratique de la Moulure de Finition
Consultez la Page 19 de ce Manuel d'Instruction pour les détails de cesprocédures.
-7-
FRANÇAIS
Parts
Diagrammes d’application duale 4Ω
JUMPER
SERIES
PARALLEL
Jumper Plug
Input
-
+
FRANÇAIS
JUMPER
1 amplificateur mono
1 (un) caisson de basse
Cavalier branché en Parallèle
Impédance de charge de
8Ω(4Ω+4Ω)
Mono
Bi-Amp
Only
Input
Input
-
+
4Ω
SERIES
-
+
Mono
4Ω
PARALLEL
Jumper Plug
1 amplificateur mono
1 (un) caisson de basse
Cavalier branché en Série
Impédance de charge de
8Ω(4Ω+4Ω)
8Ω
Bi-Amp
Only
Input
-
+
4Ω
4Ω
2Ω
*JUMPER is Removed
1 amplificateur mono
1 (un) caisson de basse
Cavalier branché en Parallèle
Impédance de charge de 8Ω(4Ω+4Ω)
SERIES
Configuration en double amplification
2 amplificateurs mono
*JUMPER is Removed
1 (un) caisson de basse Cavalier débranché
Impédance de charge de 4Ω
PARALLEL
SERIES
Input
Stereo
-
+
Bi-Amp
Only
+
PARALLEL
Input
-
Mono
Input
4Ω 2-Chan
-
+
4Ω
Bi-Amp
Only
Input
-
+
Mono
4Ω
JUMPER
1 amplificateur mono
2 (deux) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel
Impédance de charge de 4Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
4Ω
Bi-Amp
Only
Input
-
+
Input
-
+
4Ω
8Ω
PARALLEL
Jumper Plug
4Ω
Bi-Amp
Only
Input
-
+
4Ω
8Ω
4Ω
JUMPER
1 amplificateur mono
3 (trois) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel
Impédance de charge de 2.6Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
4Ω
Bi-Amp
Only
-
Input
-
+
4Ω
4Ω
8Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Bi-Amp
Only
Input
-
+
Input
-
+
4Ω
8Ω
PARALLEL
Jumper Plug
4Ω
Bi-Amp
Only
Input
-
+
4Ω
8Ω
2.6Ω
JUMPER
1 amplificateur mono
4 (quatre) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel
Impédance de charge de 2Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
4Ω
Bi-Amp
Only
8Ω
-
4Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
4Ω
Bi-Amp
Only
8Ω
2Ω
-8-
-
4Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
4Ω
Bi-Amp
Only
8Ω
Input
-
+
4Ω
PARALLEL
Jumper Plug
Input
-
+
4Ω
Bi-Amp
Only
8Ω
+
Input
-
4Ω
Diagrammes d’application duale 2Ω
JUMPER
PARALLEL
Jumper Plug
Input
-
+
Mono
Bi-Amp
Only
Input
Input
-
+
2Ω
SERIES
-
+
Mono
2Ω
PARALLEL
4Ω
Bi-Amp
Only
Input
-
+
2Ω
2Ω
1Ω
*JUMPER is Removed
1 amplificateur mono
1 (un) caisson de basse
Cavalier branché en Parallèle
Impédance de charge de 4Ω(2Ω+2Ω)
SERIES
Configuration en double amplification
2 amplificateurs mono
*JUMPER is Removed
1 (un) caisson de basse Cavalier débranché
Impédance de charge de 2Ω
PARALLEL
SERIES
Input
Stereo
-
+
Bi-Amp
Only
+
PARALLEL
Input
-
Mono
Input
2Ω 2-Chan
-
+
2Ω
Bi-Amp
Only
Input
-
+
Mono
2Ω
JUMPER
1 amplificateur mono
2 (deux) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel
Impédance de charge de 2Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
2Ω
Bi-Amp
Only
Input
-
+
Input
-
+
2Ω
4Ω
PARALLEL
Jumper Plug
2Ω
Bi-Amp
Only
Input
-
+
2Ω
4Ω
2Ω
JUMPER
1 amplificateur mono
3 (trois) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel
Impédance de charge de 1.3Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
2Ω
Bi-Amp
Only
-
Input
-
+
2Ω
2Ω
4Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Bi-Amp
Only
Input
-
+
Input
-
+
2Ω
4Ω
PARALLEL
Jumper Plug
2Ω
Bi-Amp
Only
Input
-
+
2Ω
4Ω
1.3Ω
JUMPER
1 amplificateur mono
4 (quatre) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel
Impédance de charge de 1Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
2Ω
Bi-Amp
Only
4Ω
-
2Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
2Ω
Bi-Amp
Only
4Ω
1Ω
-9-
-
2Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
2Ω
Bi-Amp
Only
4Ω
Input
-
+
2Ω
PARALLEL
Jumper Plug
Input
-
+
2Ω
Bi-Amp
Only
4Ω
+
Input
-
2Ω
FRANÇAIS
SERIES
JUMPER
1 amplificateur mono
1 (un) caisson de basse
Cavalier branché en Parallèle
Impédance de charge de
4Ω(2Ω+2Ω)
Jumper Plug
1 amplificateur mono
1 (un) caisson de basse
Cavalier branché en Série
Impédance de charge de
4Ω(2Ω+2Ω)
Pour installer l’enceinte hermétique
Si le haut-parleur ne peut pas être fixé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des
spécifications données dans le tableau ci-dessous; le
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
MDF—20 mm (3/4 pouce) est recommandé pour le matériau
A 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
de l’enceinte.
B 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
C 11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm)
D 9-4/32 inch (232 mm)
10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm)
11-10/32 inch (295 mm)
F 4/32 inch (3 mm)
4/32 inch (3 mm)
3
3
G 1.57 ft (0.045 m )
2.17 ft3 (0.062 m3)
Écrans acoustiques avant et arrière (x 2)
C
FRANÇAIS
B
Faces supérieure et
inférieure (x 2)
G : Volume interne
A
Faces gauche et
droite (x 2)
Faces gauche
et droite (x 2)
* Vis: Dia. 4mm x 50mm (x 8) (fournis)
Pour installer l’enceinte hermétique
Si le haut-parleur ne peut pas être fixé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des
spécifications données dans le tableau ci-dessous; le
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
MDF—20 mm (3/4 pouce) est recommandé pour le matériau
A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm)
de l’enceinte.
B 18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm)
C 13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm)
D 9-23/32 inch (247 mm)
10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm)
11-10/32 inch (295 mm)
F 4/32 inch (3 mm)
4/32 inch (3 mm)
G 1 inch (25.4 mm)
1 inch (25.4 mm)
H 13 inch (330.2 mm)
14 inch (355.6 mm)
I 13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm)
Écrans acoustiques avant et arrière (x 2)
J 1.85 ft3 (0.052 m3)
2.54 ft3 (0.072 m3)
C
B
Faces supérieure et
inférieure (x 2)
J : Volume interne
A
G
I
* Vis: Dia. 4mm x 50mm (x 8) (fournis)
Faces gauche et
droite (x 2)
H
Faces gauche
et droite (x 2)
- 10 -
CS-AW7020
CS-AW7040
REMARQUES
parallel
series
parallel
series
Impédance nominale (Ω)
2Ω + 2Ω
4Ω + 4Ω
SPL (dB,1W/1M)
83.49 dB 83.54 dB 84.02 dB 84.12 dB SPL : Niveau de pression sonore
0.123 ft3
Déplacement (Liter)
Dia. 9 - 6/32 inch
Diamètre du tuou de découpe (pouces)
( 233 mm )
(mm)
6 - 14/32 inch
Profondeur de montage (pouces)
( 163.5 mm )
(mm)
Re : Résistance de la bobine mobile
Re (Ω)
0.98 Ω
3.83 Ω
1.92 Ω
7.6 Ω
en CC
BL : Produit de la densité de flux et de
la longueur efficace de fil de la bobine
6.85
13.75
8.68
17.21
BL (T.M)
mobile
Vas : Volume d'air égal à la conformité
Vas (Iitre)
17.08 L
16.98 L
18.08 L
18.28 L
de l'excitateur
Vas (CuFt)
0.599 ft3
0.64 ft3
0.65 ft3
0.6 ft3
Me (g)
145.986 g 147.109 g 124.084 g 122.443 g Me : Masse effective
Dia. 202 mm
D (mm)
D : Diamètre effectif du cône
Fs : Résonance à l'air libre de
Fs (Hz)
39.6 Hz
39.5 Hz
41.7 Hz
41.8 Hz
l'excitateur
Qms
10.261
Qes
Qts
10.282
9.021
9.169
0.756
0.74
0.83
0.824
0.704
0.691
0.76
0.756
600 W
Pe [max.] (W)
Xmax. (mm)
Réponse en fréquence (Hz)
Masse de l’aimant (once)
(g)
Diamètre de la bobine mobile (pouces)
(mm)
Hvc (mm)
Hag (mm)
14.95 mm
14.8 mm
25 ~500 Hz
65.4 oz
( 1854.1 g )
Dia. 2 - 5/32 inch
Dia. 2 - 4/32 inch
( 54.5 mm )
( 53.59 mm )
39.9 mm
39.6 mm
10 mm
Qms : Q de l'excitateur à Fs considérant
uniquement la résistance non-électrique
Qes : Q de l'excitateur à Fs considérant
uniquement la résistance électrique
Qts : Q total de l'excitateur à Fs
Pe[max.] : Puissance d'entrée
continue maximum
Xmax. : Déplacement effectif maximum
de la bobine mobile sans distorsion
Hvc : Hauteur de la bobine mobile
Hvc : Hauteur de la bobine mobile
CS-AW7220
CS-AW7240
Paramètres
REMARQUES
parallel
series
parallel
series
Impédance nominale (Ω)
2Ω + 2Ω
4Ω + 4Ω
SPL (dB,1W/1M)
85.2 dB
85.87 dB 85.65 dB SPL : Niveau de pression sonore
85.13 dB
0.18 ft3
Déplacement (Liter)
Dia. 10 - 29/32 inch
Diamètre du tuou de découpe (pouces)
( 277 mm )
(mm)
7 - 6/32 inch
Profondeur de montage (pouces)
( 182.5 mm )
(mm)
Re : Résistance de la bobine mobile
Re (Ω)
0.98 Ω
3.84 Ω
1.94 Ω
7.61 Ω
en CC
BL : Produit de la densité de flux et de l
a longueur efficace de fil de la bobine
6.84
13.72
9.56
19.14
BL (T.M)
mobile
Vas : Volume d'air égal à la conformité
Vas (Iitre)
38.7 L
38.76 L
35.23 L
35.05 L
de l'excitateur
Vas (CuFt)
1.37 ft3
1.24 ft3
1.24 ft3
1.37 ft3
Me (g)
171.854 g 172.934 g 157.028 g 157.336 g Me : Masse effective
Dia. 246 mm
D (mm)
D : Diamètre effectif du cône
Fs : Résonance à l'air libre de
Fs (Hz)
34.6 Hz
34.5 Hz
37.9 Hz
38 Hz
l'excitateur
Qms
10.277
10.089
8.931
9.014
Qes
0.786
0.765
0.794
0.781
Qts
0.73
0.711
0.73
0.719
600 W
Pe [max.] (W)
Xmax. (mm)
Réponse en fréquence (Hz)
Masse de l’aimant (once)
(g)
Diamètre de la bobine mobile (pouces)
(mm)
Hvc (mm)
Hag (mm)
14.95 mm
14.8 mm
23 ~500 Hz
86.2 oz
( 2443.7 g )
Dia. 2 - 5/32 inch
Dia. 2 - 4/32 inch
( 54.5 mm )
( 53.59 mm )
39.9 mm
39.6 mm
10 mm
- 11 -
Qms : Q de l'excitateur à Fs considérant
uniquement la résistance non-électrique
Qes : Q de l'excitateur à Fs considérant
uniquement la résistance électrique
Qts : Q total de l'excitateur à Fs
Pe[max.] : Puissance d'entrée
continue maximum
Xmax. : Déplacement effectif maximum
de la bobine mobile sans distorsion
Hvc : Hauteur de la bobine mobile
Hvc : Hauteur de la bobine mobile
FRANÇAIS
Paramètres
Le agradecemos la adquisición del Altavoz Estereofónico para Automóvil de
ARSENAL. Para efectuar una instalación segura y para que el altavoz funcione
correctamente, lea detenidamente las siguientes instrucciones.
ESPAŃOL
Parts
2. Screw x 10
3. Jump
4. Fuse (10A) x 2
5. Hexagon socket
screw keys
1. Grille
Instalación y uso correctos
1.Antes de conectar los altavoces con el amplificador, confirme que esté cortada la
alimentación eléctrica. El ruido producido al realizar la conexión con la alimentación
conectada puede causar daños en los altavoces.
2.Deben conectares los terminales correspondientes del amplificador y de los
altavoces, es decir izquierdo a izquierdo y derecho a derecho,asi co mo “+” a “+” y
“–” a “–”. Si las polaridades se co nectan inversamente, la reproducción este
reofónica se deteriorará.
3.No someta los altavoces a una entrada excesiva. La capacidad máxima de los
CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 es de 600 votios (POTENCIA
MUSICAL R.M.S.). Una entra da excesiva dañará los altavoces.
4.Los CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 tienen 2Ω,4Ω,8Ω de
impedancia. Asegúrese de que la impe dancia de salida del terminal para altavoces
de amplificador sea de 2Ω, 4Ω,8Ω.
5.Cuando limpie los altavoces, utilice un paño suave y frote la superficie con cuidado.
No aplique solventes ni diluyentes.
6.Asegurese de seguir cuidadosamente las instrucciones para:
Conecciones de Cable
Reemplazo de fucible
Cambiando el Selector de Resistencia
Instalar el subwoofer y la moldura del anillo
Consulte la Page 19 de este Manual de Instrucciones para los detalles de estos
procedimientos.
- 12 -
Diagramas de Aplicasion Dual 4Ω
JUMPER
SERIES
JUMPER
1 amplificador monofónico
1(un) bajo
Puente fijado en Paralelo
Carga a 8Ω(4Ω+4Ω)
PARALLEL
SERIES
Jumper Plug
-
+
Mono
Bi-Amp
Only
Input
Input
-
+
4Ω
Jumper Plug
Input
PARALLEL
-
+
Mono
4Ω
8Ω
Bi-Amp
Only
Input
-
+
4Ω
4Ω
2Ω
*JUMPER is Removed
Amplificador 1,2 ch
1(un) bajo
Se quita el puente
Carga a 4Ω
SERIES
Input
Stereo
-
+
Configuracion Bi-Amplificada
2 amplificadores monofónicos
1(un) bajo Se quita el puente Carga a 4Ω
*JUMPER is Removed
PARALLEL
Bi-Amp
Only
+
SERIES
Mono
Input
-
Input
-
+
4Ω
PARALLEL
Bi-Amp
Only
Input
-
+
Mono
4Ω 2-Chan
4Ω
JUMPER
1 amplificador monofónico
2 (Dos) bajos
Puente fijado en serie
Subwoofers wired in Parallel
Carga a 4Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
4Ω
Bi-Amp
Only
Input
-
+
Input
-
+
4Ω
8Ω
PARALLEL
Jumper Plug
4Ω
Bi-Amp
Only
Input
-
+
4Ω
8Ω
4Ω
JUMPER
1 amplificador monofónico
3 (Tres) bajos
Puente fijado en serie
Subwoofers wired in Parallel
Carga a 2.6Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
4Ω
Bi-Amp
Only
-
Input
-
+
4Ω
4Ω
8Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Bi-Amp
Only
Input
-
+
Input
-
+
4Ω
8Ω
PARALLEL
Jumper Plug
4Ω
Bi-Amp
Only
Input
-
+
4Ω
8Ω
2.6Ω
JUMPER
1 amplificador monofónico
4 (Cuatro) bajos
Puente fijado en serie
Subwoofers wired in Parallel
Carga a 2Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
4Ω
Bi-Amp
Only
8Ω
-
4Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
4Ω
Bi-Amp
Only
8Ω
2Ω
-
- 13 -
4Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
4Ω
Bi-Amp
Only
8Ω
Input
-
+
4Ω
PARALLEL
Jumper Plug
Input
-
+
4Ω
Bi-Amp
Only
8Ω
+
Input
-
4Ω
ESPAŃOL
1 amplificador monofónico
1(un) bajo
Puente fijado en serie
Carga a 8Ω(4Ω+4Ω)
Diagramas de Aplicasion Dual 2Ω
JUMPER
1 amplificador monofónico
1(un) bajo
Puente fijado en serie
Carga a 4Ω(2Ω+2Ω)
SERIES
JUMPER
1 amplificador monofónico
1(un) bajo
Puente fijado en Paralelo
Carga a 4Ω(2Ω+2Ω)
PARALLEL
SERIES
Jumper Plug
-
+
Mono
Bi-Amp
Only
Input
Input
-
+
2Ω
Jumper Plug
Input
-
+
Mono
2Ω
4Ω
Bi-Amp
Only
Input
-
+
2Ω
2Ω
1Ω
*JUMPER is Removed
ESPAŃOL
PARALLEL
Amplificador 1,2 ch
1(un) bajo
Se quita el puente
Carga a 2Ω
SERIES
Input
Stereo
-
+
Configuracion Bi-Amplificada
2 amplificadores monofónicos
1(un) bajo Se quita el puente Carga a 2Ω
*JUMPER is Removed
PARALLEL
Bi-Amp
Only
+
SERIES
Mono
Input
-
Input
-
+
2Ω
PARALLEL
Bi-Amp
Only
Input
-
+
Mono
2Ω 2-Chan
2Ω
JUMPER
1 amplificador monofónico
2 (Dos) bajos
Puente fijado en serie
Subwoofers wired in Parallel
Carga a 2Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
2Ω
Bi-Amp
Only
Input
-
+
Input
-
+
2Ω
4Ω
PARALLEL
Jumper Plug
2Ω
Bi-Amp
Only
Input
-
+
2Ω
4Ω
2Ω
JUMPER
1 amplificador monofónico
3 (Tres) bajos
Puente fijado en serie
Subwoofers wired in Parallel
Carga a 1.3Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
2Ω
Bi-Amp
Only
-
Input
-
+
2Ω
2Ω
4Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Bi-Amp
Only
Input
-
+
Input
-
+
2Ω
4Ω
PARALLEL
Jumper Plug
2Ω
Bi-Amp
Only
Input
-
+
2Ω
4Ω
1.3Ω
JUMPER
1 amplificador monofónico
4 (Cuatro) bajos
Puente fijado en serie
Subwoofers wired in Parallel
Carga a 1Ω
SERIES
JUMPER
PARALLEL
SERIES
Jumper Plug
Input
-
+
Mono
2Ω
Bi-Amp
Only
4Ω
-
2Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
2Ω
Bi-Amp
Only
4Ω
1Ω
-
- 14 -
2Ω
PARALLEL
SERIES
Jumper Plug
Input
+
JUMPER
Input
-
+
2Ω
Bi-Amp
Only
4Ω
Input
-
+
2Ω
PARALLEL
Jumper Plug
Input
-
+
2Ω
Bi-Amp
Only
4Ω
+
Input
-
2Ω
Para instalar la caja sellada
Cuando el altavoz no se pueda instalCuando el altavoz no se pueda instalCuando el altavoz no se pueda instalusar MDF—20 mm (3/4 pulg.) como
material para la caja.
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
A 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
B 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
C 11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm)
D 9-4/32 inch (232 mm)
10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm)
11-10/32 inch (295 mm)
F 4/32 inch (3 mm)
4/32 inch (3 mm)
3
3
G 1.57 ft (0.045 m )
2.17 ft3 (0.062 m3)
Pantallas acústicas delantera y trasera (x 2)
B
Lados superior e
inferior (x 2)
G : El Volumen interior
A
Lados izquierdo y
derecho (x 2)
Dimensión del
orificio de
montaje
* Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado)
Para instalar la caja sellada
Lados superior e inferior (x 2)Cuando el altavoz no se pueda instalar en el automóvil, construya la caja sellada recomendada en la tablade
abajo—Asimismo, serecomienda usar
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
MDF—20 mm(3/4 pulg.) como material para la caja.
A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm)
B 18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm)
C 13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm)
D 9-23/32 inch (247 mm)
10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm)
11-10/32 inch (295 mm)
F 4/32 inch (3 mm)
4/32 inch (3 mm)
G 1 inch (25.4 mm)
1 inch (25.4 mm)
H 13 inch (330.2 mm)
14 inch (355.6 mm)
I 13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm)
Pantallas acústicas delantera y trasera (x 2)
J 1.85 ft3 (0.052 m3)
2.54 ft3 (0.072 m3)
C
B
Lados superior e
inferior (x 2)
J : El Volumen interior
A
G
I
* Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado)
H
- 15 -
Lados izquierdo y
derecho (x 2)
Dimensión del
orificio de
montaje
ESPAŃOL
C
CS-AW7020
CS-AW7040
NOTAS
parallel
series
parallel
series
Impedancia nominal (Ω)
2Ω + 2Ω
4Ω + 4Ω
83.49 dB 83.54 dB 84.02 dB 84.12 dB SPL : Nivel de presión de sonido
SPL (dB,1W/1M)
0.123 ft3
Desplazamiento (litro)
Dia. 9 - 6/32 inch
Diámetro del orificio cortado (pulgada)
( 233 mm )
(mm)
6 - 14/32 inch
Profundidad de montaje (pulgada)
( 163.5 mm )
(mm)
Re : Resistencia de la bobina móvil de
0.98 Ω
3.83 Ω
1.92 Ω
7.6 Ω
Re (Ω)
CC
BL : Producto de densidad de flujo y
longitud efectiva del cable de la
6.85
13.75
8.68
17.21
BL (T.M)
bobina móvil
Vas: Volumen de aire equivalente en
17.08 L
16.98 L
18.08 L
18.28 L
Vas (litro)
conformidad con el excitador
Vas (pies cúbicos)
0.599 ft3
0.64 ft3
0.65 ft3
0.6 ft3
145.986 g 147.109 g 124.084 g 122.443 g Me : Masa efectiva
Me (g)
Dia. 202 mm
D (mm)
D : Diámetro efectivo del cono
ESPAŃOL
Parámetros
Fs (Hz)
39.6 Hz
39.5 Hz
41.7 Hz
41.8 Hz
Qms
10.261
10.282
9.021
9.169
Qes
0.756
0.74
0.83
0.824
Qts
0.704
0.691
0.76
0.756
600 W
Pe [máx.] (W)
Xmax. (mm)
Respuesta de frec (Hz)
Masa del imán (oz)
(g)
Diám.de la bobina móvil (pulgada)
(mm)
Hvc (mm)
Hag (mm)
14.95 mm
14.8 mm
25 ~500 Hz
65.4 oz
( 1854.1 g )
Dia. 2 - 5/32 inch
Dia. 2 - 4/32 inch
( 54.5 mm )
( 53.59 mm )
39.9 mm
39.6 mm
10 mm
Fs : Resonancia del aire sin excitador
Qms : Q del excitador a Fs considerando
sólo la resistencia no eléctrica
Qes : Q del excitador a Fs considerando
sólo la resistencia eléctrica
Qts : Total Q dei excitador a Fs
Pe[max.] : Potencia máxima de
entrada contínua
Xmax. : Máximo desplazamiento
efectivo de la bobina móvil sin distorsón
Hvc : Altura de bobina móvil
Hag : Altura de entrehierro
CS-AW7220
CS-AW7240
Parámetros
NOTAS
parallel
series
parallel
series
Impedancia nominal (Ω)
2Ω + 2Ω
4Ω + 4Ω
85.2 dB
85.87 dB 85.65 dB SPL : Nivel de presión de sonido
85.13 dB
SPL (dB,1W/1M)
0.18 ft3
Desplazamiento (litro)
Dia. 10 - 29/32 inch
Diámetro del orificio cortado (pulgada)
( 277 mm )
(mm)
7 - 6/32 inch
Profundidad de montaje (pulgada)
( 182.5 mm )
(mm)
Re : Resistencia de la bobina móvil de
0.98 Ω
3.84 Ω
1.94 Ω
7.61 Ω
Re (Ω)
CC
BL : Producto de densidad de flujo y
longitud efectiva del cable de la
6.84
13.72
9.56
19.14
BL (T.M)
bobina móvil
Vas: Volumen de aire equivalente en
38.7 L
38.76 L
35.23 L
35.05 L
Vas (litro)
conformidad con el excitador
Vas (pies cúbicos)
1.37 ft3
1.24 ft3
1.24 ft3
1.37 ft3
171.854 g 172.934 g 157.028 g 157.336 g Me : Masa efectiva
Me (g)
Dia. 246 mm
D (mm)
D : Diámetro efectivo del cono
Fs (Hz)
34.6 Hz
34.5 Hz
37.9 Hz
38 Hz
Qms
10.277
10.089
8.931
9.014
Qes
0.786
0.765
0.794
0.781
Qts
0.73
0.711
0.73
0.719
600 W
Pe [máx.] (W)
Xmax. (mm)
Respuesta de frec (Hz)
Masa del imán (oz)
(g)
Diám.de la bobina móvil (pulgada)
(mm)
Hvc (mm)
Hag (mm)
14.95 mm
14.8 mm
23 ~500 Hz
86.2 oz
( 2443.7 g )
Dia. 2 - 5/32 inch
Dia. 2 - 4/32 inch
( 54.5 mm )
( 53.59 mm )
39.9 mm
39.6 mm
10 mm
- 16 -
Fs : Resonancia del aire sin excitador
Qms : Q del excitador a Fs considerando
sólo la resistencia no eléctrica
Qes : Q del excitador a Fs considerando
sólo la resistencia eléctrica
Qts : Total Q dei excitador a Fs
Pe[max.] : Potencia máxima de
entrada contínua
Xmax. : Máximo desplazamiento
efectivo de la bobina móvil sin distorsón
Hvc : Altura de bobina móvil
Hag : Altura de entrehierro
ES
OL
h
inc ] H
/32 mm
h
7
c
.5
n
a.
2i
Di [ 5
80/3 ]
-2 mm
1
1
5
a. [ 29
Di
ES
OL
h
nc ] H
2i m
3
h
/
7 .5 m
inc
a.
Di [ 5 3/32 m ]
82
9- 7 m
a. [ 24
i
D
Dia. 12-24/32 inch [ 324 mm ]
7-7/32 inch [ 182.5 mm ]
1-9/32 inch
[ 32.69 mm ]
Dia. 12-12/32 inch [ 314 mm ]
6-14/32 inch [ 163.5 mm ]
Dia. 10-26/32 inch [ 275 mm ]
1-9/32 inch
[ 32.51 mm ]
Dia. 10-14/32 inch [ 265 mm ]
Dia. 9-4/32 inch [ 231.96 mm ]
Dia. 10-28/32 inch [ 275.94 mm ]
CS-AW7020
CS-AW7040
CS-AW7220
CS-AW7240
- 17 -
Multi Mount Smart
Trim Ring
(Patent Pending)
Santoprene Surround
Glass Fiber
Laminated
Hemp Cone
Air Vented
Aluminum
Cast Basket
Integlated Dual-Layer
Cone construction
Hemp-Fiber Drive
Cone
Woven Tinsel Lead
(Patent Pending)
Dual Diametric
Progressive Spider
Rapid Fire Impedance
Selector Speaker Terminal
( Patent Pending)
Aluminum Voice
Coil Former
Dual Stacked
Strontium Magnet
4 (2+2) Layer Voice Coils
Heat Transfer Silicon
Heat Transfer Silicon
Aero Vent Bottom Plate
T3 Chassis (Thermal Transfer Technology)
- 18 -
- 19 -
TO OUR VALUED CUSTOMER
THANK YOU FOR PURCHASING THIS JVC PRODUCT.
WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE.
NEED HELP ON HOW TO HOOK UP?
NEED ASSISTANCE ON HOW TO OPERATE?
NEED TO LOCATE A JVC SERVICE CENTER?
LIKE TO PURCHASE ACCESSORIES?
IS HERE TO HELP!
TOLL FREE: 1(800)252-5722
http://www.jvc.com
Remember to retain your Bill of Sale for Warranty Service.
Do not attempt to service the product yourself
Caution
To prevent electrical shock, do not open the cabinet.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
EN, FR, SP
© 2007 Victor Company of Japan, Limited
Printed in China