IFM O1D102 Mode d'emploi

PDF
Document
Manuel de l'utilisateur IFM O1D102 - Détecteur de distance optique | Fixfr
/

User questions

P E

John P.

How to configure the O1D102 sensor to deactivate the output when an object is detected at a distance of less than 100 cm?

To deactivate the output (stop the signal) below 100 cm, use output OUT1 configured with the [Hnc] (Normally Closed) function. First, set the display unit [Uni] to [mm]. Then, set the output function [OU1] to [Hnc] and the switching threshold [SP1] to 1000. In this configuration, the output remains active at distances greater than 1000 mm and opens (deactivates) when the object is closer than 1000 mm.

P E

John P.

How to configure the distance sensor to deactivate the output when an object is detected closer than 100 cm?

To deactivate the output when an object is within 100 cm, configure the switching output to the Hysteresis Normally Closed [Hnc] function with a threshold of 1000 mm. Follow these steps: 1. Set the display unit [Uni] to [mm]. 2. Set the output function [OU1] to [Hnc]. 3. Adjust the switching point [SP1] to 1000. 4. Wait 15 seconds to return to Run mode. In this mode, the output remains active when the object is far and opens (stops) when the distance falls below 1000 mm.

P E

John P.

How to configure the O1D102 optical distance sensor?

To configure the sensor, follow these general steps: 1. Press [MODE/ENTER] until the desired parameter appears. 2. Hold [SET] and adjust the value by brief or prolonged presses. 3. Briefly press [MODE/ENTER] to confirm. 4. Wait 15 seconds or press [MODE/ENTER] to return to Run mode. It is recommended to set the display unit ([Uni]) first.

P E

John P.

How to configure the sensor's OUT1 output to stop (open) if an object is detected below 100 cm (1000 mm)?

To configure OUT1 to stop (open) when an object is detected below 100 cm (1000 mm), follow these steps:

  1. Ensure the unit is set to mm: Press [MODE/ENTER] until [Uni] appears. Hold [SET] and press it until [mm] is displayed. Confirm with [MODE/ENTER].
  2. Configure OUT1 function: Press [MODE/ENTER] repeatedly until [OU1] appears. Hold [SET] and press it until [Hnc] is selected. Confirm with [MODE/ENTER].
  3. Set the threshold: Press [MODE/ENTER] until [SP1] appears. Hold [SET] and press it to increase or decrease the value until it reaches 1000 (representing 100 cm). Confirm with [MODE/ENTER].
  4. Finalize: Wait 15 seconds or press [MODE/ENTER] until the measured distance is displayed again to return to Run mode.
P E

John P.

How to configure the O1D102 sensor to deactivate the output when an object is detected closer than 100 cm?

Use output OUT1 and set its function [OU1] to [Hnc] (Normally Closed) and the switching threshold [SP1] to 1000 mm. This ensures the output opens (stops) when the distance is below 100 cm. Ensure the display unit [Uni] is set to [mm] for accurate threshold setting.

P E

John P.

How to configure a sensor output to stop when an object is detected below a certain distance?

Use the hysteresis function on output OUT1 with the [Hnc] (normally closed) setting. Set the threshold [SP1] to the desired distance value (e.g., 1000 for 100 cm). In this configuration, the output remains active when the object is far and deactivates when the object moves closer than the defined threshold.

D F

Linda D.

How to configure the sensor output to 100 mm in normally closed mode?

To set OUT1 to 100 mm in normally closed mode (Hnc) on your O1D102 detector, first navigate to the [OU1] parameter and select [Hnc]. Then, go to the [SP1] parameter, hold [SET] to make the value blink, and adjust it to 100 (mm). Confirm with [MODE/ENTER]. Ensure the display unit [Uni] is set to [mm].

D F

Linda D.

How to configure the sensor output to open when the detected distance is below 1000 mm?

To make OUT1 open when the detected distance D is below 1000 mm, set the [OU1] parameter to [Hnc] (hysteresis, normally closed). Then, navigate to the [SP1] parameter and set its value to 1000 mm. With [Hnc], the output is defined as "open" when D is less than [SP1].

D F

Linda D.

How to configure the sensor output to open when the measured distance is below a specific threshold?

Access the [OU1] menu and set the output mode to [Hnc] (hysteresis function, normally closed). Then, access the [SP1] parameter and adjust the value to the desired distance (e.g., 1000 mm). The output will remain open as long as the detected distance is below this set threshold.

D F

Linda D.

How to configure the O1D102 sensor output (OUT1) to open when the measured distance is below a specific threshold?

To set the output to open when the distance is lower than a set point (e.g., 1000 mm), use the hysteresis function in normally closed mode [Hnc]. 1. Press [MODE/ENTER] until [OU1] appears, select [Hnc] using [SET], and confirm with [MODE/ENTER]. 2. Press [MODE/ENTER] until [SP1] appears, hold [SET] to adjust the value to your threshold (e.g., 1000), and confirm with [MODE/ENTER].

D F

Linda D.

How to configure the O1D102 sensor output (OUT1) to activate (open) when the detected distance is less than 1000 mm?

To configure the OUT1 output of the O1D102 sensor to activate (open) when the distance is less than 1000 mm:

  1. Access the [OU1] menu by pressing [MODE/ENTER].
  2. Select [Hnc] (normally closed hysteresis function) using [SET], then confirm with [MODE/ENTER].
  3. Define the [SP1] threshold: Press [MODE/ENTER] to select [SP1]. Hold [SET] to adjust its value to 1000 mm, then confirm with [MODE/ENTER]. Note: With [Hnc] setting, the output is defined as « open » when the distance D is less than the [SP1] threshold (1000 mm).
Preparing document for printing…
0%