Intex Piscine Tubulaire Prism Frame Rectangulaire 4,00 X 2,00 X 1,00 M Mode d'emploi

PDF
Document
Intex Piscine Tubulaire Prism Frame Rectangulaire 4,00 X 2,00 X 1,00 M Mode d'emploi | Fixfr
/

User questions

Y Z

Michael Y.

How to install the U-shaped legs of a pool?

No votes

After assembling the horizontal beams, insert the tongue (13) into the U-shaped leg (11). Insert the U-shaped leg into the holes of the horizontal beams by pressing the double-clips until they click and lock into place. Pull the bottom of the leg outward to fully stretch the tongues. If the ground is not stable, place a piece of marine plywood (38 x 38 x 3 cm) under each leg, centering the leg on the board.

Y Z

Michael Y.

How to install the U-shaped feet of a swimming pool?

No votes

To install the U-shaped feet of a swimming pool, follow these steps: 1. After assembling the horizontal beams, insert the strap into the U-shaped foot. 2. Insert the U-shaped foot into the holes of the horizontal beams by pressing the double-clips until they lock into place with a click. 3. Pull the bottom of the foot outward to fully stretch the straps. 4. If the ground is not hard and stable, place a 38 x 38 x 3 cm marine plywood board under each foot, centering the foot on the plate.

Y Z

Michael Y.

How to install the U-shaped feet of a pool?

No votes

To install the U-shaped pool feet, follow these steps: 1. After assembling the horizontal beams, insert the tab (13) into the U-foot (11). 2. Insert the U-foot into the holes of the horizontal beams by pressing the double-clips until they click into place. 3. Pull the bottom of the foot outward to fully stretch the tabs. 4. If the ground is not stable, place a piece of marine plywood (38 x 38 x 3 cm) centered under each U-foot.

Y Z

Michael Y.

How to install the U-shaped legs of the pool?

No votes

Pour installer les pieds en U de votre piscine, veuillez suivre ces étapes conformément au manuel d'utilisation : 1. Après avoir assemblé les poutres horizontales, insérez la languette (13) dans le pied en U (11). 2. Insérez ensuite le pied en U dans les trous des poutres horizontales. Les pieds en U sont équipés de double-clips ; appuyez avec vos doigts sur ces clips pour insérer le pied dans la poutre. Relâchez le clip une fois en place ; vous devriez entendre un claquement signifiant que la pièce est verrouillée. 3. Une fois l'assemblage effectué, tirez le bas du pied vers l'extérieur pour étirer au maximum les languettes. 4. Si le sol n'est pas dur et stable, placez une pièce de bois contreplaqué marin (38 x 38 x 3 cm) sous chaque pied en U, en positionnant le pied au centre de la plaque.

Y Z

Michael Y.

How to install the U-shaped feet of the pool?

No votes

To install the U-shaped feet of your pool, follow these steps according to the user manual: 1. After assembling the horizontal beams, insert tab (13) into the U-foot (11). 2. Then insert the U-foot into the holes of the horizontal beams. The U-feet are equipped with double-clips; press these clips with your fingers to insert the foot into the beam. Release the clip once in place; you should hear a click indicating that the part is locked. 3. Once assembled, pull the bottom of the foot outwards to stretch the tabs as much as possible. 4. If the ground is not hard and stable, place a piece of marine plywood (38 x 38 x 3 cm) under each U-foot, positioning the foot in the center of the plate.

Y Z

Michael Y.

How to install the pool legs?

No votes

To install the U-shaped feet of your pool, please follow these steps according to the user manual: 1. After assembling the horizontal beams, insert the tab (13) into the U-shaped foot (11). 2. Then insert the U-shaped foot into the holes of the horizontal beams. The U-shaped feet are equipped with double clips; press these clips with your fingers to insert the foot into the beam. Release the clip once in place; you should hear a click indicating that the piece is locked. 3. Once assembled, pull the bottom of the foot outwards to stretch the tabs as much as possible. 4. If the ground is not hard and stable, place a piece of marine plywood (38 x 38 x 3 cm) under each U-shaped foot, positioning the foot in the center of the plate.

Y Z

Michael Y.

How to install the U-shaped legs of a swimming pool?

No votes

To install the U-shaped legs, first assemble the horizontal beams and insert the tab (13) into the U-leg (11). Insert the leg into the holes of the beams by pressing the double-clips until you hear a click. Finally, pull the bottom of the leg outward to fully stretch the tabs. On soft or unstable ground, place a piece of marine plywood (38 x 38 x 3 cm) under the center of each leg.

Y Z

Michael Y.

How are the pool feet installed?

No votes

To install the U-shaped feet of your pool, follow these steps: 1. After assembling the horizontal beams, insert the tab (13) into the U-foot (11). 2. Then insert the U-foot into the holes of the horizontal beams. The U-feet have double-clips; press these clips with your fingers to insert the foot into the beam. Release the clip once in place; you should hear a click indicating it's locked. 3. Once assembled, pull the bottom of the foot outwards to stretch the tabs as much as possible. 4. If the ground is not hard and stable, place a piece of marine plywood (38 x 38 x 3 cm) under each U-foot, centering the foot on the plate.

Y Z

Michael Y.

How are the U-shaped pool legs installed?

No votes

To install the U-shaped pool legs, insert the tab (13) into the U-leg (11), then insert the U-leg into the holes of the horizontal beams. The U-legs have double-clips; press them to insert the leg, and release once in place until you hear a click. After assembly, pull the bottom of the leg outwards to maximize the tab stretch. If the ground is not hard and stable, place a piece of marine plywood (38 x 38 x 3 cm) under each U-leg, centering the leg on the plate.

F D

Linda F.

How to assemble the pool structure?

No votes
  1. Prepare a flat, level site and lay the ground cloth. 2. Spread the liner and position the drain valve. 3. Insert horizontal beams into the liner sleeves. 4. Attach U-shaped legs to the beams until the clips lock. 5. Assemble corners and the ladder. 6. Fill with water to the inner fill line. No tools are required for assembly.
F D

Linda F.

How to assemble the frame pool?

No votes

Place the ground cloth on flat ground and lay out the liner. Insert the horizontal beams into the liner edges and snap the U-shaped legs into the beams. Assemble the corners and ladder, ensure all valves are closed, and fill with water to the inner fill line.

Preparing document for printing…
0%